Thor sculpt and the goats are coming along

After a week of working on all sort of things, like Blue Dragonflies for a swap I joined in our clay group, this is where I am now with my Thor sculpt.

Baked body Thor

I have sculpted the upper part of the body, attached the head and gave it a first bake. When it had cooled I attached the tubes for the arm and leg modules with Magic Sculpt and let it dry overnight. Now I have to make the hands and feet, bake them and attach them to finish the body. Looking at it I am not really sure if the head is too small?  Still have to work on the neck too and that will show if I have to rip the head off again and redo that part 🙂

Goat frame

These are the frames for Tanngrisni and Tanngnost, the two goats who will be pulling Thor’s chariot. The bottom one is already filled out with aluminum foil and painters tape, the top ones shows the wire before bulking it out.

Goats clay

And here are Tanngrisni and Tanngnost, the wire covered with Prosculpt and baked. What I need to do now is paint the hooves and horns, put hair on them which will also cover up where I didn’t put enough clay on the frame, and when it is all done and ready to go in front of the chariot I’ll paint the eyes on.

This is what I’ve done so far since last week. Hope you like it!


Finally started

I’ve been busy getting ready for a show so I didn’t have a lot of time to sculpt on my Thor, eventhough my fingers were itching to start. Collected most of what I think I will need: got a piece of bark for the chariot to stand on, found wood to make the chariot with, found an old piece of a coat (collar) that had faux ‘wool’ on it that would be great for the goats since it is rather long.

Found and collected all sort of other things I think I might need, or not, so I picked it up again for a bit and made the drawing couple of days ago. After that I made the frame and started on the head.

I have to apologize for the bad quality of the pictures. My camera stopped working, tried my phone but that one froze so I had to open it up to remove the battery and somewhere along the line I must have messed up the contact point for the camera because that one doesn’t want to work at all… I’ll re-open that when I have the time.

Drawing and frame

The tubes are cut but having a little problem there with keep getting confused as to what goes in where… Since it isn’t going to be a tall sculpt, only about 5′-5.5″, there won’t be a lot of pressure on the joints and I could leave the whole tube-idea out too, except for the legs; it is easier to attach the legs to the chariot using the whole tube system.

Bulk and head

I can tell I haven’t done it in a while because I really have to pay attention that the head isn’t going to be too large for the frame. It looks okay for now but I have the feeling I have to make a new frame, just a bit larger than the one I have now which would be okay because I can always use this frame for another sculpt.

The bulking out of the frame is done with aluminum foil and painters tape although the chest needs to be larger, as you can see on the side view of the picture above. However, I can do that with clay too.

This is the first time I am using ProSculpt and I have to say I like it. It is really smooth, easy to condition, and it blends in great! Compared to other polymer clay brands like Sculpey, Fimo and Premo that I have used before for small(er) sculptures, it is softer, more pliable, and I have to say that I am sold on this one 🙂

Still have to make the chariot sketch and found some ideas online; it is going to be like the chariot in the example I’ll use and posted on March 30th so I might ‘wing it’ and make it straight from that example after the sculpt is complete. Then I only have to measure twice and cut once.

Here is where I am at this moment. Have to attach the ears and then the head will go for the first bake and see how it will look on this frame that I have now. Hope you like it so far!

Thor, chariots, and helmets

Yesterday evening I started on the sketch of Thor and trying to figure out other things for my sculpt, like the not unimportant chariot. Have to make a sketch of that one too…

One of the biggest problems I have is that there are no real references as to the chariots Norsemen used and plenty of discussions if the Norse people used them or not. There is the Celtic chariot, with a single axle, the Egyptian and Roman, also with a single axle, and then I come across the “Oseberg cart” with a double axle. I know this is a cart and not a chariot but Googling images for “Viking/Norse Chariots” gives me all sort of confusing information, showing single and double axle chariots.

Thor is shown in both single and double axle chariots, while Freya is only shown in her cat-drawn single axle chariot.

So I have to make a choice here and this is what it’s going to be… the double axle chariot based on this picture that I like:


This is a drawing of Thor, made in 1901 by the German painter Johannes Gehrts and, unlike some paintings/drawings, Thor has a beard. I have mentioned it before, I’m going to stick to the Norse visualization of Thor, being red-haired, red-bearded, fiery eyed, and barrel-chested. He is, after all, the most valiant Warrior of the Norse Pantheon and an idealized image of the Viking fighter.

And he is not wearing any helmet of some sort, another reason for choosing this picture to work off. Looking for information on the Norse and their Pantheon, you will find lots of discussions. One of those discussion is if the Vikings wore helmets or not. We all know that Vikings are often shown with helmets with horns but apparently that is wrong. If the average Viking warrior wore a helmet, it would have been a non-descript conical form helmet without any adorations (I won’t go into the “wings” decoration because they have been used). Planting horns on a helmet would give your enemy the chance to grab onto those…something you wouldn’t want.

Now, to plant a non-descript conical form helmet on Thor would look silly, in my humble opinion, and very un-God like wouldn’t you think?

Off to the drawingboard for the chariot and next time I will post my sketches.

Hope you’ll have a great day!